*Note these are just the variables my triple osc was at when i made this, you could probably do better if you tried
also that variable may be very precise, again this is just the way i found it
For the (PLUGIN) tab;
make sure the first 2 modes on top are set to [MIX]
for all the Oscillators set the wave to
Other than that you can leave OSC1 alone.
For OSC2 on the other hand set OSC2's Course detuneing [CRS] to -12, thats all for OSC2.
Now for OSC3 set the [CRS] -24.
Now move to the (ENV/LFO) Tab and the (Volume) sub tab;
Set the [DEL] to 0, if 0 is the default for [DEL] and [ATT] which i think it is don't mess with them, or actually do, experiment around and see what happens.
(top half)
Set the [DEC] to max (2)
Set the [SUST] to .787
Set the [REL] to .1
Set [AMT] to 1
Next to LFO;
make sure the wave is gray, if it is green click on it and it will turn gray.
Set the LFO[DEL] to .042
Set the LFO[ATT] to .013
Set the LFO[SPD] to .1
Filter should be [ON], set at LowPass, [FREQ] set to 9031 Hz and [RESO] to 4.8
Now move to (CUROOF) SubTab;
Set [HOLD] to .5
Set [DEC] to .5
Set [SUST] to .5
Set [REL] to .1
Nexto to (CUTOFF)'s LFO
[DEL] 0
[ATT] 0
[SPD] .1
[AMT] 0
Filter should be same as on volume tab
Now move to the (FUNC)
[STACKING] OFF
[Chord] OCTAVE
[ARPEGGIO] OFF
[CHORD] OCTAVE
[DIRECTION] UP
[MODE] FREE
Both [Range]'s should be 0
[GATE] 100
*NOTE I don't know how many of these Effects are actually being used
Now move to (FX) Tab
add the TAP Chorus/Flanger [W/D] MAX, all else is 0
for TAP Chorus/Flanger click Controls,
Now set these variables;
Frequency [Hz] 1.25
L/R Phase Shift [deg] 90
Depth [%] 34.375
Delay [ms] 25
Contour [Hz] 99.9
Dry Level [dB] 1.7875
Wet Level [dB] 19.9375
Your done with that window so you can close it
Your now done! Thank You for reading
also that variable may be very precise, again this is just the way i found it
For the (PLUGIN) tab;
make sure the first 2 modes on top are set to [MIX]
for all the Oscillators set the wave to
Other than that you can leave OSC1 alone.
For OSC2 on the other hand set OSC2's Course detuneing [CRS] to -12, thats all for OSC2.
Now for OSC3 set the [CRS] -24.
Now move to the (ENV/LFO) Tab and the (Volume) sub tab;
Set the [DEL] to 0, if 0 is the default for [DEL] and [ATT] which i think it is don't mess with them, or actually do, experiment around and see what happens.
(top half)
Set the [DEC] to max (2)
Set the [SUST] to .787
Set the [REL] to .1
Set [AMT] to 1
Next to LFO;
make sure the wave is gray, if it is green click on it and it will turn gray.
Set the LFO[DEL] to .042
Set the LFO[ATT] to .013
Set the LFO[SPD] to .1
Filter should be [ON], set at LowPass, [FREQ] set to 9031 Hz and [RESO] to 4.8
Now move to (CUROOF) SubTab;
Set [HOLD] to .5
Set [DEC] to .5
Set [SUST] to .5
Set [REL] to .1
Nexto to (CUTOFF)'s LFO
[DEL] 0
[ATT] 0
[SPD] .1
[AMT] 0
Filter should be same as on volume tab
Now move to the (FUNC)
[STACKING] OFF
[Chord] OCTAVE
[ARPEGGIO] OFF
[CHORD] OCTAVE
[DIRECTION] UP
[MODE] FREE
Both [Range]'s should be 0
[GATE] 100
*NOTE I don't know how many of these Effects are actually being used
Now move to (FX) Tab
add the TAP Chorus/Flanger [W/D] MAX, all else is 0
for TAP Chorus/Flanger click Controls,
Now set these variables;
Frequency [Hz] 1.25
L/R Phase Shift [deg] 90
Depth [%] 34.375
Delay [ms] 25
Contour [Hz] 99.9
Dry Level [dB] 1.7875
Wet Level [dB] 19.9375
Your done with that window so you can close it
Your now done! Thank You for reading