LMMS • Forums

Posted: **June 5th, 2018, 1:09 pm**

When I make an automation to some parameter ,close and open my project, LMMS assigns it to an other, random parameter. I'm running it on windows 10 64bit.

Posted: **June 5th, 2018, 5:43 pm**

What version of lmms are you using?

Posted: **June 6th, 2018, 10:57 am**

igg.go123 wrote: ↑
June 5th, 2018, 1:09 pm
::

First, Welcome to the Forum igg.go123 !
Here are all important links:
http://lmms.io/forum/viewtopic.php?f=1&t=4740
-A few rules and useful forum instructions

LMMS assigns automation to an other, random parameter.

Sounds like automation-ID loss, so you are talking about copied blocks of automation -right?
They are not assigned to something 'random'
All you have to do, is to re-drag the controller into the 'rogue' automation block. Both the connection and the curve will be re-established.
Best time to do this, is emediately after a block of automation has been copied.
Its a bug. It will be fixed
@zonk : eg its #3781

If i was wrong, and this was not it, then please post your:
* OS subtype (home-pro(?)
* lmms version

Posted: **June 6th, 2018, 12:14 pm**

musikbear wrote: ↑
June 6th, 2018, 10:57 am

igg.go123 wrote: ↑
June 5th, 2018, 1:09 pm
::
First, Welcome to the Forum igg.go123 !
Here are all important links:
http://lmms.io/forum/viewtopic.php?f=1&t=4740
-A few rules and useful forum instructions

LMMS assigns automation to an other, random parameter.

Sounds like automation-ID loss, so you are talking about copied blocks of automation -right?
They are not assigned to something 'random'
All you have to do, is to re-drag the controller into the 'rogue' automation block. Both the connection and the curve will be re-established.
Best time to do this, is emediately after a block of automation has been copied.
Its a bug. It will be fixed
@zonk : eg its #3781

If i was wrong, and this was not it, then please post your:
* OS subtype (home-pro(?)
* lmms version

I think i'm using windows pro
I'm using lmms 1.2.0 rc5

Posted: **June 6th, 2018, 4:54 pm**

igg.go123 wrote: ↑
June 6th, 2018, 12:14 pm
I think i'm using windows pro
I'm using lmms 1.2.0 rc5

Ok.. But have you tried what i wrote -redrag the controller into the automation-block?
If that 'fixes' it, it is a known issue, nothing need to be done now, but if not, its a new one, and devs have to look at that too

Posted: **June 6th, 2018, 6:05 pm**

musikbear wrote: ↑
June 6th, 2018, 10:57 am

igg.go123 wrote: ↑
June 5th, 2018, 1:09 pm
::
First, Welcome to the Forum igg.go123 !
Here are all important links:
http://lmms.io/forum/viewtopic.php?f=1&t=4740
-A few rules and useful forum instructions

LMMS assigns automation to an other, random parameter.

Sounds like automation-ID loss, so you are talking about copied blocks of automation -right?
They are not assigned to something 'random'
All you have to do, is to re-drag the controller into the 'rogue' automation block. Both the connection and the curve will be re-established.
Best time to do this, is emediately after a block of automation has been copied.
Its a bug. It will be fixed
@zonk : eg its #3781

If i was wrong, and this was not it, then please post your:
* OS subtype (home-pro(?)
* lmms version

I also noticed that happends with copied chanels.

Posted: **June 7th, 2018, 4:22 pm**

igg.go123 wrote: ↑
June 6th, 2018, 6:05 pm
I also noticed that happends with copied chanels.

DO this!
-redrag the controller into the automation-block!
does it solve the problem?

LMMS • Forums

(Windows) Automation doesn't work correct

(Windows) Automation doesn't work correct

Re: (Windows) Automation doesn't work correct

Re: (Windows) Automation doesn't work correct

Re: (Windows) Automation doesn't work correct

Re: (Windows) Automation doesn't work correct

Re: (Windows) Automation doesn't work correct

Re: (Windows) Automation doesn't work correct